4430 search results for fla

4550201-724origind

4550201-724origind

6490000-2.origind

on one flat with a corresponding reference mark on the base plate at each bolt. Then incrementally turn, consisting of a machine screw (#8-5/8 inch long), nut and two 6490000 All Jobs flat washers (1/4 inch inside diameter) and lock washer. Tightly clamp the screen layers between the flat washers

6490000.origind

of each tip nut in a snug-tight condition with a suitable marking on one flat with a corresponding, stainless steel fastener assembly consisting of a machine screw (#8-5/8 inch long), nut and two flat washers (1/4 inch inside diameter) and lock washer. Tightly clamp the screen layers between the flat

6490000.impl

the reference position of each tip nut in a snug-tight condition with a suitable marking on one flat, flat washers (1/4 inch inside diameter) and lock washer. Tightly clamp the screen layers between the flat washers. 649-7 Structural Grout Pads. On mast arm support structures, install a structural

6490000-Man02.impl

position of each tip nut in a snug-tight condition with a suitable marking on one flat, consisting of a machine screw (No. 8, 5/8 inch long), nut and two flat washers (1/4 inch inside diameter) and lock washer. Tightly clamp the screen layers between the flat washers. 649-7 Structural

SS7000000

. Provide all sign panels with a flat surface. 700-5 Fabrication of Retroreflectorized Sign Faces, flat head machine screws with nuts and lock washers to give a flat surface for the overlay panel

SS5610000

and upper explosive limits, flash point, boiling point, amount of volatile organic compounds by weight

SS5610000

and upper explosive limits, flash point, boiling point, amount of volatile organic compounds by weight

9160000.FHWA

Minimum 99.0% (Not applicable for PG 76-22 (ARB)) Flash Point, AASHTO T 48-06 (2010) Cleveland, 20% Particle Charge Test (c) positive Test on Residue: (d) Flash Point COC minimum 410ºF, % (Not applicable for PG 76-22 (ARB)) Flash Point, AASHTO T 48-06 (2010) Cleveland Open Cup Minimum

DEV712-971IMP (12-17-20)

D4060 (5) 350 mg Flash Point ASTM D92 500°F 1.72-hour freeze cycle at 15 degrees F

3200300-723 FHWA

required for the various mixtures. Heat the material in such a manner that no flame comes in contact, for the various mixtures. Heat the material in such a manner that no flame comes in contact

RTrafficControlSignalsand Devices

RTrafficControlSignalsand Devices

RTrafficControlSignalsand Devices

9970000-724IMPL

and bottom to deter tampering. Cabinet Door Double flanged on all four sides and equip it with a restraint

44592625201-PLANS-03-SIGNALIZATION

CLEARANCE FLASHING DON'T WALK 3 INITIAL GREEN (MIN) 5 - EXTENSION (GAP) 15 15 50 - WBT SBL 2 4, 8 4 7 8 TF 3 P4 P6 - S.O.P. 10 (MODIFIED) MINOR STREET IS BIRD KEY DR (25 MPH). 2. FLASHING, CONTROLLER PHASE ALL RED CLEARANCE FLASHING DON'T WALK 3 INITIAL GREEN (MIN) 5 - EXTENSION (GAP, STREET IS SUNSET DR / GOLDEN GATE PT (25 MPH). 2. FLASHING OPERATION: MOVEMENTS 6 YELLOW, ALL, Crossing TIME REMAINING DON'T CROSS STEADY TIMER FLASHING TO CROSS PUSH BUTTON DO NOT BLOCK

9160000.origind

76-22 (ARB)) Flash Point, AASHTO T 48-06 (2010) Cleveland Open Cup Minimum 450ºF Rotational, Tests on Emulsion: Test on Residue: (d) Flash Point COC minimum 410ºF Viscosity 140ºF 6 0 0

9005 - Contract Document

Tackifier – Clings to vertical surfaces Flash Point - >120 degree F. Evaporation - >24 Hours, residue Flash Point - >120 degree F. Evaporation - >12 Hours Viscosity – Sprayable liquid

Agency Term Contract - Asphalt Tar Remover

Tackifier – Clings to vertical surfaces Flash Point - >120 degree F. Evaporation - >24 Hours, residue Flash Point - >120 degree F. Evaporation - >12 Hours Viscosity – Sprayable liquid